Manage stand orders
Select Option

Sea & Sea Benelux BV

Nijverheidstraat 6g Rood, 3144 CL Maassluis
Netherlands

Hall map

boot 2020 hall map (Hall 11): stand K31

Fairground map

boot 2020 fairground map: Hall 11

Our range of products

Product categories

  • 08  Diving
  • 08.01  Diving Gear
  • 08.01.03  Lighting / Underwater Video / Photography
  • 08  Diving
  • 08.01  Diving Gear
  • 08.01.04  Diving Suits / Jackets

Diving Suits / Jackets

  • 08  Diving
  • 08.01  Diving Gear
  • 08.01.06  Diving Accessories

Diving Accessories

  • 08  Diving
  • 08.01  Diving Gear
  • 08.01.07  Diving Fashion

Diving Fashion

Our products

Product category: Lighting / Underwater Video / Photography

YS-D2 Flitser

Sea & Sea YS-D2J Underwater strobe
Product No. 03121

The complete underwater strobe which realizes power, speed and quality.

Features:
Excellent night-time visibility. The illuminated control panel is ideal for night diving
Color of illumination changes to indicate mode: aqua blue (in DS-TTL mode), blue (in slave TTL mode), orange (in manual pre-flash mode) and Green (in manual mode without pre-flash). You can check which mode the strobe is set even under pitch-black conditions.

Maximum guide number is a powerful 32 (ISO 100, meter). Recycle time is only 1.5 sec(*1)
The YS-D2 is powerful enough to illuminate a wide area, even under very bright conditions with plenty of natural sunlight. During macro photography, where subtle exposure control is required, manual mode can easily be selected and the guide number quickly adjusted as low as 1.
(*1) when nickel hydride AA batteries are used.

DS-TTL ll automatic exposure control with improved accuracy and stability
SEA&SEA’s own automatic exposure control system, DS-TTL ll, has been further improved. Tuning light emitting timing in detail and adding light emission detection function, the accuracy of automatic TTL exposure has been noticeably improved. Previously, TTL photography was difficult with the lens’s aperture wide-open (maximum aperture) and images were likely to be overexposed. It is now possible to give a low powered flash so the correct exposure can be easily achieved with the YS-D2.

EV control function can finely tune the amount of light emitted
By controlling the actual flash light level, the strobe achieves accurate exposure compensation with EV compensation. As the exposure compensation range has improved to +/- 2.0 EV, users can concentrate on shooting even more creative images. (-2,0EV, -1.5EV, -1EV, -0.7EV, -0.3EV, +0.3EV, +0.7EV, +1EV, +1.5EV, +2.0EV).

Two diffusers and red filters included with the strobe as standard
By attaching one of the included diffusers, the beam angle is increased to 100o or 120o (circular) with a soft and even light. The red target light filter helps avoid disturbing skittish creatures that are likely to react to normal light. The red filter is fitted inside the diffusers.
Diffuser100 for YS-D1/D2 Diffuser(standard accessory)
Diffuser120 for YS-D1/D2 Diffuser(standard accessory)

The target light can be adjusted in 2 steps
The strobe is equipped with a target light (approximately 100/300 lumen). In use (target light switch in ON position), the light will be automatically turn off when the strobe fires and will automatically turn back ON after 0.5 sec.

Ergonomically improved controls
Handling is greatly improved. Larger knobs and a new magnetic rotary switch help prevent controls being accidentally reset in use. With the new controls, quick operation is possible when photo opportunities suddenly appear.

Custom mode is a new innovation which allows the YS-D2 to be compatible with cameras with non-standard pre-flash settings
Some manufactures use their own pre-flash timings on their cameras. The new custom function means the YS-D2 can be compatible with cameras with non-standard pre-flash in DS-TTLII and manual modes.

Attaching the YS-D2
The strobe can be attached to an arm with the ball-mount and with the YS-mount. The ball mount is a standard accessorie. The YS-Mount is optional.

Choosing the right cable
In accordance with the camera and housing you use, choose either a fiber-optic cable (optional) or sync cord (optional) to connect the strobe.
* A Fiber-optic cable ll is required to use the DS-TTL ll function.

[Guide Number (ISO 100/m) (land)] : 32, 24 (with Diffuser 100 attached), 20 (with Diffuser 120 attached)
[Beam Angle] : 80°x80° (without Diffuser), 100°x100°(Diffuser 100), 120° x 120° (Diffuser 120)
[Batteries] : 4xAA A: 6V Ni-MH: 4.8V
[Number of Flashes *1] : A: 150 Ni-MH: 200
[Recycle time (full) *2] : A: 3.0 sec. Ni-MH: 1.5 sec.
[Color temperature] : 5600K
[Color temperature w/diffuser] : 5250K
[Depth rating] : 100m / 330ft
[Dimensions (WxHxD)] : 89x111x141mm / 3.5 x 4.8 x 5.6 inches (excluding YS-base)
[Weight] : 618g / 21.0oz (w/o batteries) (excluding YS-base)
[Underwater weight] : Approx.+40g / 1.4oz (incl. batteries)
[Others]
Exposure control: DS-TTL II, Slave TTL, Light level control dial (GN): 1 / 1.4 / 2 / 2.8 /4 / 5.6 /8 / 11 / 16 / 22 / 32 (11 steps)
Pre-flash control: Equipped with pre-flash cancel mode
DS-TTL II function
Slave function
Auto power OFF function
Sync cord: 5-pin Sync cord/N, Fiber-Optic Cable
Over-pressure relief valve
LED target light (output is adjustable in 2 steps)
Audible charge signal

*1 Number of flashes and recycle time depends on the battery brand, temperature and frequency of use.
*2 Number of flashes and recycle time of Ni-MH batteries were tested on 2400 mAh batteries.
The complete underwater strobe which realizes power, speed and

More Less

Product category: Lighting / Underwater Video / Photography

M67 Wide angle Conversion Lens 0,6x

M67 Wide-angle Conversion Lens 0.6x
Product No.52123

A wide-angle conversion lens with M67 screw mount.
When the lens is mounted, the angle of view increases from 28mm to about a maximum of 17mm (35mm film camera equivalent). The lens can be detached and attached underwater; it can also be used on land.
· Use of an external strobe is strongly recommended; using the built-in flash when the lens is mounted may cause shadows to appear in images.
·The lens is compatible with the MDX-RX100III,MDX-RX100/II, MDX-X10* ,the Nikon WP-N1+ / WP-N2*/ WP-N3, the Olympus PT-EP06L, PT-EP05L as of March 2015.
* For starred (*) housings, slightly zoom to telephoto side to avoid vignetting.

[Lens] 3 elements in 3 groups
[Underwater angle of view] 94 degrees (150 degrees on land)
[Magnification] 0.6x
[Depth rating] 60m/200ft
[Weight] 426g / 15oz (220g / 7.8oz underwater)
[Dimensions (DIA x D)] 96 x 44mm / 3.8 x 1.7 inches
[Construction] corrosion-resistant aluminum alloy, anodized body (black).

More Less

Product category: Lighting / Underwater Video / Photography

MDX-5D Mark lV housing (black)

Features

Important controls can be operated whilst holding the grips. Frequently-used buttons such as ISO, AF Point Selection and Multi-function Selection buttons are operated by external levers, allowing quick and accurate operation.
AF Start button is locked by pressing and turning the control.
AF Start Lever will remain pressed by pushing the lever forward.

The main command dial, the quick control dial and others have a damper (spring) to provide secure operation. (Controls on the camera will not slip because of the damper).

The tension on the Shutter Release lever can be adjusted in 3 steps
The tension on the Shutter Release lever can be adjusted in 3 steps, by changing the location of the spring inside the housing. The distance to half-depress the shutter release can be adjusted in 2 steps, by changing the location of the plastic piece behind the shutter lever, inside the housing.

Compatible with Optical YS Converter/C
Equipped with two fiber-optic cable sockets for optional Optical YS Converter/C.
*Serial numbers YSC200094 and above are compatible. Serial numbers below YSC200094 are not compatible. New firmware will be required.

MDX-5D Mark IV Other Features

-The Port Lock prevents the port from turning or loosening and the Port Lock lever is specifically located to avoid being unlocked accidentally.
-The housing is equipped with a lens-lock release button which makes it possible to change lenses easily, without opening the housing.
-The camera’s diopter adjustment dial can be operated from outside the housing. This feature is useful when two or more people with different eyesight use the housing.
-Pulling out the Focus/Zoom Dial gives sufficient room inside the housing to easily accommodate larger diameter lenses.
-All controls have luminescence stickers which glow in dark environment.
-Equipped with the Optical Viewfinder 0.5x as standard. Other optional viewfinders such as the VF180 1.2x, VF45 1.2x and Optical Viewfinder 0.8x can be used.
-Sync Cord 2-pin Connector enables use of conventional hardwired Sync cable (Manual mode only).
-Accessory port enables use of Leak Sentinel (vacuum sensor).

-Equipped with two sacrificial zinc diodes (one on the front case and the other on the rear) to prevent electrolysis damage.
-Built-in leak sensor immediately alerts you to water ingress.
-Tripod screw mount is located on the centre underside of the housing.

Specifications
MDX-5D Mark IV
Construction: Corrosion-resistant aluminum alloy (machined, anodized finish)
Grip: Corrosion-resistant die-cast aluminum alloy
Depth Rating: 100m/330ft
Dimensions (WxHxD): 341 x 198 x 141mm /13.4 x 7.8 x 5.5 inches
Weight (Approx.): 3,000g/106oz (Housing only)
Artikelnummer: Canon-MDX-5D Mark IV Categorie: Behuizingen Tag: Sea & Sea

More Less